Skip to content
Shop this Manufacturer by Category
-
-
-
- The 4 inch wide tread width provides added comfort while boarding or exiting your boat or dock.
- Select Options
This product has multiple variants. The options may be chosen on the product page
-
-
-
- The 4 inch wide tread width provides added comfort while boarding or exiting your boat or dock.
- Select Options
This product has multiple variants. The options may be chosen on the product page
-
-
-
- Scottco Marine manufactures our own galvanized Steel Truss Frames. These frames are each 10 feet in length and 8" high with 2" angle. They come in 2', 3', 4', 5', 6', and 8' widths. Special custom sizes available upon request.
- Select Options
This product has multiple variants. The options may be chosen on the product page
-
-
-
- 3 feet wide steps with handrails for stability. Choose your decking on the steps.
- Select Options
This product has multiple variants. The options may be chosen on the product page
-
-
-
- 1/4" galvanized steel truss frame single 'T' hinges, to be used with Scottco manufactured Steel Truss Frames. To create a hinge between frames use Truss Frame Hinge Female (TF-HF) and Truss Frame Hinge Male (TF-HM).
- Add to Estimate
-
-
-
- Outside Corner End Hardware for Wood Dock Kit. (WH-OCE) The outside corner end is used at the ends of dock, ends of fingers, or corners of swim platforms.
- Add to Estimate
-
-
-
- Outside Corner Male for Wood Dock Kit. (WH-OCM) The Outside Corner Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Female (WH-OCF) or with a Single "T" Female (WH-SF) at the corner of your dock to attach a finger or dock section.
- Add to Estimate
-
-
-
- Outside Corner Female for Wood Dock Kit. (WH-OCF) The Outside Corner Female has two 1/2" tabs with holes for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Male (WH-OCM) or with a Single "T" Male (WH-SM) at the corner of your dock to attach a finger or dock section.
- Add to Estimate
-
-
-
- Inside Corner Hardware for Wood Dock Kit. (WH-IC) The inside corner, working opposite the outside corner, sandwiches the wood, keeping bolts from burying themselves in the wood. This corner gusset will give the dock a lot of strength and stability.
- Add to Estimate
-
-
-
- Single "T" Male for Wood Dock Kit. (WH-SM) The Single "T" Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Female (WH-SF) or Outside Corner Female (WH-OCF). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock.…
- Add to Estimate
-
-
-
- Single "T" Female for Wood Dock Kit. (WH-SF) The Single "T" Female has two 5/8" tabs with holes for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Male (WH-SM) or Outside Corner Male (WH-OCM). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock.…
- Add to Estimate
-
-
-
- Angle Hardware for Wood Dock Kit. (WH-A) Angles are used with a Washer Plate (WH-W) to hold cross stringers to side stringers. These two pieces of steel sandwich the wood, creating a solid corner.
- Add to Estimate
-
-
-
- Backup Plate for Wood Dock Kit. (WH-B) Use the Backup Plate with our Single "T" Males (WH-SM) and Single "T" Females (WH-SF) for additional strength. They also keep the bolts from pulling through your wood.
- Add to Estimate
-
-
-
- (WHP-3) Our 3" Pipe Holder bolts to a side stringer. Use a 2" standard pipe to anchor your dock in place.
- Add to Estimate
-
-
-
- Washer Plate for Wood Dock Kit. (H-W) The washer plate is used primarily with Angles (H-A) and Cleat Angles (H-CA). The plate has two square holes to keep the carriage bolts from turning when tightening them.
- Add to Estimate
-
-
-
- (WH-CRS) Our Chain Retainer bolts to the side of your dock and uses chain to hold the dock in place. You can use 5/16", 3/8" or 1/2"chain. Use either (2) H-W or (1) B as back up plates. 5" L x 5"
- Add to Estimate
-
-
-
- Outside Corner Female/Female for Wood Dock Kit. (WH-OCFF) Made to add a finger on the corner, and saves using a WH-SM or WH-SF.
- Add to Estimate
-
-
-
- Outside Corner Male/Male for Wood Dock Kit. (WH-OCMM) Made to add a finger on the corner, and saves using a WH-SM or WH-SF.
- Add to Estimate
-
-
-
- Outside Corner Female/Male for Wood Dock Kit. (WH-OCFM) Made to add a finger on the corner, and saves using a H-SM or H-SF.
- Add to Estimate
-
-
-
- Cleat Angle for Wood Dock Kit. (WH-CA) The cleat angle has slots that accommodate various cleat sizes. Bolt the cleat angle to the side stringer using a Washer Plate (WH-W). Then bolt the cleat through the deck into the cleat angle. This will ensure that the cleat will not pull out of the deck.
- Add to Estimate
