Wood Dock Hardware
We manufacture our heavy duty boat dock hardware using 1/4″ steel. If you use the right materials the first time, it will ensure you a dock that will be able to ride out those high winds and choppy waters. All dock hardware is made for 1/2″ carriage bolts and is hot dipped galvanized after fabrication. Our hardware can be used with up to 4″ thick lumber. Need some help knowing where everything goes? Our experienced staff can help. Contact us.
Placement Guide
Hardware for Wood Dock Kits
Our bundles include all the hardware and floats you need to build your dock with our free dock kit plans.
All Wood Dock Hardware Products
-
Outside Corner End (WH-OCE)
- Outside Corner End Hardware for Wood Dock Kit. (WH-OCE) The outside corner end is used at the ends of dock, ends of fingers, or corners of swim platforms.
- Add to Estimate
-
Outside Corner Male (WH-OCM)
- Outside Corner Male for Wood Dock Kit. (WH-OCM) The Outside Corner Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Female (WH-OCF) or with a Single "T" Female (WH-SF) at the corner of your dock to attach a finger or dock section.
- Add to Estimate
-
Outside Corner Female (WH-OCF)
- Outside Corner Female for Wood Dock Kit. (WH-OCF) The Outside Corner Female has two 1/2" tabs with holes for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Male (WH-OCM) or with a Single "T" Male (WH-SM) at the corner of your dock to attach a finger or dock section.
- Add to Estimate
-
Inside Corner (WH-IC)
- Inside Corner Hardware for Wood Dock Kit. (WH-IC) The inside corner, working opposite the outside corner, sandwiches the wood, keeping bolts from burying themselves in the wood. This corner gusset will give the dock a lot of strength and stability.
- Add to Estimate
-
Single “T” Male (WH-SM)
- Single "T" Male for Wood Dock Kit. (WH-SM) The Single "T" Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Female (WH-SF) or Outside Corner Female (WH-OCF). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock.…
- Add to Estimate
-
Single “T” Female (WH-SF)
- Single "T" Female for Wood Dock Kit. (WH-SF) The Single "T" Female has two 5/8" tabs with holes for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Male (WH-SM) or Outside Corner Male (WH-OCM). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock.…
- Add to Estimate
-
Angle (WH-A)
- Angle Hardware for Wood Dock Kit. (WH-A) Angles are used with a Washer Plate (WH-W) to hold cross stringers to side stringers. These two pieces of steel sandwich the wood, creating a solid corner.
- Add to Estimate
-
Backup Plate (WH-B)
- Backup Plate for Wood Dock Kit. (WH-B) Use the Backup Plate with our Single "T" Males (WH-SM) and Single "T" Females (WH-SF) for additional strength. They also keep the bolts from pulling through your wood.
- Add to Estimate
-
3″ Pipe Holder (WHP-3)
- (WHP-3) Our 3" Pipe Holder bolts to a side stringer. Use a 2" standard pipe to anchor your dock in place.
- Add to Estimate
-
Washer Plate (WH-W)
- Washer Plate for Wood Dock Kit. (H-W) The washer plate is used primarily with Angles (H-A) and Cleat Angles (H-CA). The plate has two square holes to keep the carriage bolts from turning when tightening them.
- Add to Estimate
-
Chain Retainers (WH-CRS)
- (WH-CRS) Our Chain Retainer bolts to the side of your dock and uses chain to hold the dock in place. You can use 5/16", 3/8" or 1/2"chain. Use either (2) H-W or (1) B as back up plates. 5" L x 5"
- Add to Estimate
-
Outside Corner Female/Female (WH-OCFF)
- Outside Corner Female/Female for Wood Dock Kit. (WH-OCFF) Made to add a finger on the corner, and saves using a WH-SM or WH-SF.
- Add to Estimate
-
Outside Corner Male/Male (WH-OCMM)
- Outside Corner Male/Male for Wood Dock Kit. (WH-OCMM) Made to add a finger on the corner, and saves using a WH-SM or WH-SF.
- Add to Estimate
-
Outside Corner Female/Male (WH-OCFM)
- Outside Corner Female/Male for Wood Dock Kit. (WH-OCFM) Made to add a finger on the corner, and saves using a H-SM or H-SF.
- Add to Estimate
-
Cleat Angle (WH-CA)
- Cleat Angle for Wood Dock Kit. (WH-CA) The cleat angle has slots that accommodate various cleat sizes. Bolt the cleat angle to the side stringer using a Washer Plate (WH-W). Then bolt the cleat through the deck into the cleat angle. This will ensure that the cleat will not pull out of the deck.
- Add to Estimate
-
Splice Plates (WH-SP)
- Splice Plate for Wood Dock Kit. (WH-SP) Our Splice Plates were designed to join two timbers together. One is used on each side. The bolt holes are drilled so that an angle and 1/ 1/2" lumber can be added at the splice and end up at the end of the splice. Our Splice Plates are sold in pairs.
- Add to Estimate
-
Inside Corner 3″ Pipe Holder (WH-ICP3)
- (WH-ICP3) Use the Inside Corner - 3" I.D. Pipe Holder in place of a regular inside corner to accommodate a 2" I.D. pipe. The 3" Pipe Holder is welded in place.
- Add to Estimate
-
Dock Finger Stabilizers
- See diagrams for description of dock finger stabilizer parts.
- Select Options This product has multiple variants. The options may be chosen on the product page
Don't See What You're Looking For?
Reach out to us and we can help.
Not all our products are listed here and we can usually help you find what you need!